Radar 10.0 - Homeopathic Medical software

[jukasboy]

go to the directory of radar 10 and look for the file autoreg.exe an run once. the other thing you can do it is run the icon radar 10 config and choose full repertories. but I has the same problem and I solved runing radar10/autoreg.exe

[tinku]

great work sir
thanks for this software
does anyone has full version of Isis Vision or Isis V2?

[tinku]

hi all I m getting error in radar 10
and not able to use any version of synthesis repertory to repertorise
but all the other repertories r working fine and i can repertorise also but not with any of the synthesis
PLEASE HELP

[jukasboy]

It seems to be a problem with the synthesys repertories after update, but until now no one have idea how to fixed, if I found it I will post it

[scopas]

Sir, there is problem in full repertory mode and do not see Murphy 3 and SE92 even after installing the update 30 (RADARLiveUpdate1000030) and unpacked the archieve radar_10.0.030_update2. The access in Murphy 3 and SE92 is not allowed.
Can someone help?
scopas

[jukasboy]

If you want radar to load murphy and se92 at startup add this to the link property Target: mue300 SE92, ex:

C:\RADAR10\BIN\radar.exe mue300 se92

[buk]

Hi,
The update doesn't work for me. It gives an error message when I try to install it and it fails to install.
I can't see Murphy's repertory and most of the other repertories don't work as well. It says "another user is using it at the moment". Only Kent and Synthesis 8 work.
Can you help me somehow?
Thanks.

[jukasboy]

did you follow the steps in order? what's the error message? where you install radar?.
To the other repertories try this: run the icon radar 10 config in the desktop and choose full repertories.

[mufti]

RADAR 10 Installation Procedure

1)For the steps below, I assume that all the Radar 10 files (part 01 to 10) are in a folder “Radar10Files”, and the update files are in a folder “Radar10Updates” ,
on your hard disk. (The folder names are tentative). I assume that you have
already unpacked these three update files in the update folder: i) RadarLive
Update1000030, ii) Radar_10.0.030_update2, and iii) catalogfr.

2)Click on the file “Radar10.part01” and install the program on C:\Radar
or on D:\Radar. I am assuming that you will be installing on C:\Radar.

3)The install would extract all files in “C:\Radar\Radar10”.

4)When the installation is complete, go to folder “Radar10Updates” and to
“RadarLiveUpdate1000030” and double click the file inside. Check it shows the directory C:\Radar\Radar10 for updating and click.

5)Go to “Radar10Updates” and then to “Radar_10.0.030_update2”. Copy the three files therein to C:\Radar\Radar10\bin.

6) Click the icon “Radar10Config” on Desktop and click “Full Repertories.”

7) Click on “Encyclopedia Homeopathica” on Desktop. If you get an error message saying “An unsupported operation was attempted” then go to C:\Radar\Radar10
and run the file “autoreg.exe” only once.

8) Re-boot.

9) Now you are ready to run Radar 10. Click the Desktop icon. You will see a list of a large number of repertories for different languages, many of which are not available. For convenience and seeing only the available repertories, go to “Radar10Updates” and then go to “catalogfr”. Copy the two files therein into the folder C:\Radar\Radar10\System. Now you will only see the available repertories while the unavailable repertories will be replaced with blank spaces.

10) If you want Radar to load Murphy and SE92 at startup, right click the Radar icon, go to properties and add this to the target:

C:\radar\radar10\bin\radar.exe mue300 se92

11)If after all this, you get error messages or some other problem, uninstall Radar10 and remove the installed directory. Re-install the program after going through all the above steps again. For me, re-installing worked.

12)All the available repertories including Murphy3 and SE92 are working OK.

Mufti

[tinku]

@mufti
i hae done it as u told already but there is problem while i try to repertorise with any version of synthesis repertories; but, all other repertories are working fine and EH is also working fine. PLEASE TELL ME HOW I CAN REPERTORISE WITH SYNTHESIS REPERTORY
I CAN ACCESS ALL OF THEM BUT NOT ABLE TO REPERTORISE WITH SYNTHESES